{"resources":[{"slug":"board-bring-up-checklist","title":"Board Bring-up Checklist","subtitle":"A step-by-step checklist for powering a new board safely for the first time, with a results log","category":"Checklist","topic":"test-compliance","summary":"A printable checklist for bringing up a newly assembled board: inspection before power, rail resistance checks, first power on a current-limited supply, rail and sequencing checks, clocks and resets, programming and debug, peripheral checks, and a results table for recording every measurement.","formats":["PDF"],"pages":5,"courses":["hardware-bring-up-validation","power-supply-design","firmware-fundamentals"],"updatedAt":"2026-11-16T00:16:22.463Z"},{"slug":"emc-design-checklist","title":"EMC Design Checklist","subtitle":"Schematic, layout, cable, filtering, ESD and enclosure checks, plus a pre-compliance bench test list","category":"Checklist","topic":"signal-power","summary":"A printable checklist for designing electronics that pass emissions and immunity testing. Checks cover the schematic, the layout, connectors and cables, filtering, ESD and the enclosure, followed by a list of pre-compliance bench tests you can run before booking a test laboratory.","formats":["PDF"],"pages":6,"courses":["emc-by-design","regulatory-compliance","signal-integrity-fundamentals","power-supply-design"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"firmware-release-checklist","title":"Firmware Release Checklist","subtitle":"Checks to run before a firmware build ships: versioning, reproducible builds, test gates, security, updates and archiving","category":"Checklist","topic":"embedded","summary":"A printable checklist for releasing embedded firmware: version control and tagging, versioning, reproducible builds, testing gates, security checks such as signing, locked debug ports and removed secrets, update and rollback, release notes and archiving, with a release record to fill in.","formats":["PDF"],"pages":5,"courses":["firmware-fundamentals","secure-boot-firmware-updates","embedded-c","embedded-linux"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"pcb-dfm-checklist","title":"PCB Design for Manufacturing Checklist","subtitle":"Grouped fabrication checks to run before you release a bare-board design","category":"Checklist","topic":"manufacturing","summary":"A printable design for manufacturing checklist for bare printed circuit boards. Grouped checks cover stackup and materials, copper features, holes and vias, solder mask and legend, outline and panel, controlled impedance and the fabrication data package, with short notes on why each check matters.","formats":["PDF"],"pages":6,"courses":["pcb-dfm","pcb-fabrication-in-depth","pcb-stackup-design","controlled-impedance"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"layout-review-checklist","title":"PCB Layout Review Checklist","subtitle":"Checks from mechanical fit to output files, with a reviewer sign-off table","category":"Checklist","topic":"pcb-design","summary":"A printable checklist for reviewing a printed circuit board layout before release. Grouped checks cover mechanical fit, placement, power and ground, signal routing, high-speed nets, thermal design, assembly, test access, silkscreen and output files, with a sign-off table.","formats":["PDF"],"pages":6,"courses":["pcb-layout-fundamentals","signal-integrity-fundamentals","design-for-assembly-test","pcb-thermal-management"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"pcb-rfq-checklist","title":"PCB and PCBA Quote Request Checklist","subtitle":"What to send for a bare-board quote and an assembly quote, so the price is right first time","category":"Checklist","topic":"product","summary":"A printable checklist of everything to include when asking for a bare PCB quote or a PCB assembly quote: files, quantities, lead time, specifications, consigned or turnkey parts, test, packaging, plus a fill-in request summary so suppliers quote the board you actually need.","formats":["PDF"],"pages":5,"courses":["pcb-dfm","pcb-assembly-soldering","design-for-assembly-test","component-sourcing-bom"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"schematic-review-checklist","title":"Schematic Design Review Checklist","subtitle":"Concrete checks for power, pins, protection, connectors and BOM data before layout starts","category":"Checklist","topic":"pcb-design","summary":"A printable checklist for reviewing a schematic before layout. Checks cover power and decoupling, accounting for every pin, pull-ups and strapping, protection, connectors, net naming, BOM attributes and documentation, and end with a sign-off table for the reviewers.","formats":["PDF"],"pages":6,"courses":["schematic-design","power-supply-design","component-sourcing-bom","hardware-bring-up-validation"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"impedance-quick-reference","title":"Controlled Impedance Quick Reference","subtitle":"Structures, sensitivities, approximate formulas, interface targets, tolerances, drawing tables and TDR coupons","category":"Reference","topic":"signal-power","summary":"A quick reference for controlled impedance boards: the common trace structures, which parameters raise or lower impedance, the classic closed-form approximations with their validity limits and worked values, common interface targets, tolerances, what goes in the drawing's impedance table and how TDR coupons are used.","formats":["PDF"],"pages":5,"courses":["controlled-impedance","signal-integrity-fundamentals","high-speed-interfaces","pcb-stackup-design"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"electronics-glossary","title":"Electronics Manufacturing and PCB Glossary","subtitle":"Concise definitions across PCB design, fabrication, assembly, test, signal integrity, firmware and supply chain","category":"Reference","topic":"product","summary":"An alphabetical glossary of the terms engineers, buyers and project managers meet when building electronics: PCB design and fabrication, assembly and soldering, inspection and test, signal integrity, embedded firmware, and supply chain, each with a concise, practical definition.","formats":["PDF"],"pages":19,"courses":["pcb-basics","product-to-production","pcb-assembly-soldering","component-sourcing-bom"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"ipc-standards-map","title":"IPC and Electronics Standards Map","subtitle":"Which standard covers what, from design and materials to assembly, cables, data and ESD","category":"Reference","topic":"manufacturing","summary":"A one-stop map of the IPC, J-STD and ESD documents that electronics teams meet most often, grouped by life-cycle stage: terms, design, materials, bare board, assembly, cables, data exchange and ESD control, with what each covers and who uses it.","formats":["PDF"],"pages":5,"courses":["pcb-dfm","pcb-fabrication-in-depth","pcb-assembly-soldering","inspection-defects-rework"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"stackup-reference","title":"PCB Stackup Reference","subtitle":"Typical 2 to 10 layer stackups for 1.6 mm boards, symmetry rules, copper weights and a specification checklist","category":"Reference","topic":"pcb-design","summary":"A printable reference of typical starting-point stackups for 2, 4, 6, 8 and 10 layer boards around 1.6 mm thick, with the reasoning behind each layer assignment, symmetry rules, copper weight choices and a checklist of what a complete stackup specification contains.","formats":["PDF"],"pages":6,"courses":["pcb-stackup-design","controlled-impedance","pcb-materials","pcb-dfm"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"trace-width-current-reference","title":"Trace Width and Current Reference","subtitle":"IPC-2221 and IPC-2152 compared, a computed width table, copper resistance, voltage drop and via current","category":"Reference","topic":"pcb-design","summary":"A reference for sizing copper by current: how the IPC-2221 formula and the newer IPC-2152 charts differ, a width table computed from the IPC-2221 formula for 1 oz and 2 oz copper at 10 °C rise, copper resistance and voltage drop, and typical via current guidance.","formats":["PDF"],"pages":5,"courses":["pcb-dfm","pcb-thermal-management","power-supply-design","power-integrity-pdn"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"via-drill-reference","title":"Via and Drill Reference","subtitle":"Via types, finished and drilled sizes, aspect ratio, annular ring, IPC-4761 protection, microvias, back-drilling and typical drills","category":"Reference","topic":"pcb-design","summary":"A printable reference for holes and vias: via types, finished versus drilled hole size, aspect ratio, annular ring and how IPC-6012 classes treat it, the seven IPC-4761 via protection types, microvia and back-drilling basics, and a table of typical drill sizes for common uses.","formats":["PDF"],"pages":6,"courses":["pcb-dfm","hdi-microvia-design","pcb-fabrication-in-depth","signal-integrity-fundamentals"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"ipc-class-guide","title":"IPC Product Classes 1, 2 and 3 Explained","subtitle":"What the classes mean, how to choose and specify one, and the mistakes that cost money","category":"Guide","topic":"manufacturing","summary":"A practical guide to IPC product classes 1, 2 and 3: what each class means, who chooses it, how to write it on fabrication and assembly drawings and purchase orders, how the classes differ in practice, what drives the cost difference, and the common specification mistakes.","formats":["PDF"],"pages":5,"courses":["pcb-dfm","pcb-fabrication-in-depth","inspection-defects-rework","product-to-production"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"laminate-materials-guide","title":"PCB Laminate Materials Guide","subtitle":"Tg, Td, CTE, Dk, Df, T260/T288 and CAF explained, generic material classes, IPC-4101 call-outs and a selection checklist","category":"Guide","topic":"pcb-design","summary":"A guide to PCB base materials: what Tg, Td, CTE, Dk, Df, T260, T288 and CAF resistance mean and why they matter, typical ranges for generic material classes from standard FR-4 to PTFE, how to call out material by IPC-4101 slash sheet, and a selection checklist.","formats":["PDF"],"pages":5,"courses":["pcb-materials","pcb-stackup-design","controlled-impedance","pcb-fabrication-in-depth"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"surface-finish-guide","title":"PCB Surface Finish Selection Guide","subtitle":"HASL, lead-free HASL, ENIG, ENEPIG, immersion silver, immersion tin, OSP and hard gold compared, with a selection flow","category":"Guide","topic":"manufacturing","summary":"A practical guide to choosing a PCB surface finish. It profiles the eight common finishes, compares flatness, typical shelf life, wire bonding, relative cost, lead-free compatibility and typical uses in one table, and gives a step-by-step selection flow and a drawing checklist.","formats":["PDF"],"pages":5,"courses":["pcb-fabrication-in-depth","pcb-assembly-soldering","pcb-dfm","pcb-basics"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"unit-conversion-cheat-sheet","title":"Electronics Unit Conversion Cheat Sheet","subtitle":"Mils and millimetres, copper weight, wire gauge, temperature, decibels, SI prefixes and E-series values","category":"Cheat sheet","topic":"pcb-design","summary":"A printable cheat sheet of the conversions electronics engineers use daily: mil, inch, mm and µm tables, copper weight to thickness, AWG wire diameters, temperature, dB, dBm to volts in 50 Ω, SI prefixes and E12/E24 resistor values, with the formula behind every table.","formats":["PDF"],"pages":7,"courses":["pcb-basics","pcb-dfm","controlled-impedance","schematic-design"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"embedded-c-cheat-sheet","title":"Embedded C Cheat Sheet","subtitle":"Fixed-width types, bit manipulation, volatile, register access, promotion pitfalls and interrupt-safe patterns","category":"Cheat sheet","topic":"embedded","summary":"A printable cheat sheet for C on microcontrollers: stdint.h types, bit set, clear, toggle and field idioms, volatile and const, register access patterns, integer promotion and overflow traps, interrupt-safe data sharing, common undefined behaviour and a MISRA-style coding checklist.","formats":["PDF"],"pages":7,"courses":["embedded-c","firmware-fundamentals","rtos-fundamentals"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"bom-template","title":"Bill of Materials (BOM) Template","subtitle":"An editable BOM workbook with column guidance, revision history and best practice","category":"Template","topic":"product","summary":"An editable bill of materials workbook for electronic assemblies, with a note on every column, generic example rows, a revision history sheet and instructions. The PDF explains BOM best practice so your assembler can quote and build from it without guessing.","formats":["PDF","XLSX","CSV"],"pages":4,"courses":["component-sourcing-bom","product-to-production","design-for-assembly-test"],"updatedAt":"2026-11-15T23:23:00.734Z"},{"slug":"hardware-test-plan-template","title":"Hardware Test Plan Template","subtitle":"An editable test plan workbook with requirement traceability, EVT/DVT/PVT phasing and an equipment list","category":"Template","topic":"test-compliance","summary":"An editable hardware test plan workbook that links every test to a requirement, states measurable pass criteria and sample sizes, and assigns tests to EVT, DVT or PVT. Includes an equipment sheet and a guide to writing tests that can be traced and repeated.","formats":["PDF","XLSX","CSV"],"pages":4,"courses":["hardware-bring-up-validation","product-to-production","regulatory-compliance"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"fabrication-notes-template","title":"PCB Fabrication Notes Template","subtitle":"An editable fabrication drawing notes block, with an explanation of every note","category":"Template","topic":"manufacturing","summary":"An editable template for the fabrication notes on a printed circuit board drawing. The PDF explains what each note controls and why it matters; the Word document gives a fill-in notes block covering material, thickness, copper, IPC class, finish, mask, impedance, holes, vias, panel, marking, test and acceptance.","formats":["PDF","DOCX"],"pages":4,"courses":["pcb-dfm","pcb-fabrication-in-depth","controlled-impedance","pcb-materials"],"updatedAt":"2026-11-15T22:54:45.388Z"},{"slug":"certification-planner","title":"Product Certification Planning Worksheet","subtitle":"A worksheet for mapping target markets to likely requirements, standards, test houses and a test schedule","category":"Template","topic":"test-compliance","summary":"An editable worksheet for planning product certification early: list target markets, record the likely requirements and standards to confirm, choose test houses and schedule testing. The PDF summarises FCC, CE marking, UKCA and ISED regimes and gives a step-by-step planning sequence.","formats":["PDF","XLSX","CSV"],"pages":4,"courses":["regulatory-compliance","emc-by-design","iot-wireless-connectivity","product-to-production"],"updatedAt":"2026-11-15T22:54:45.388Z"}]}