Design for Assembly and Test
Lay out boards that assemble with few defects, can be tested thoroughly and can be repaired.
Go beyond basic DFM rules to design boards that assemble cleanly and can be proven good. Learn how process route and package choice set cost, how layout prevents tombstoning, bridging and voiding, how to design through-hole parts and panels for the line, and how to plan test coverage, test points, programming access and rework.
Intermediate · 5 modules · 17 lessons · free certificate
About this course
Most assembly defects and most untestable boards are designed in. A pad tied straight to a ground plane tombstones a small capacitor, a full paste aperture on a QFN thermal pad floats the part and fills the joint with voids, a connector placed beside a bottom-side BGA cannot be wave soldered, and a net with no test point can only be checked by hoping the functional test exercises it. None of these show up in a design rule check, and all of them are cheap to fix while the layout is still open.
This course follows a board from process route to final repair. It starts with the choices that set the number of assembly steps, such as one side or two, package sizes and through-hole parts, then covers spacing, orientation and polarity, the defects that layout can prevent, through-hole design for wave, selective and pin-in-paste soldering, and panels and handling. The final module covers test strategy and coverage, test point design, programming and boundary-scan access, and designing for rework. Figures from standards are named; process figures are labelled as typical and must be confirmed with your assembler and test house.
The course builds on PCB Design for Manufacturing, which introduces fiducials, placement spacing, panelisation and test access, and goes deeper on each. It does not teach how to run a soldering process or an inspection system: those are covered in PCB Assembly and Soldering and in Inspection, Defects and Rework. A course certificate records completion of the course only.
Before you start: You should have laid out at least one board and be familiar with land patterns, solder paste, fiducials and panelisation at the level of PCB Design for Manufacturing in the AAVICO Academy.
What you will learn
- Choose a process route and package mix that keeps assembly steps, cost and risk under control
- Set component spacing, orientation and polarity marking that suit placement, inspection and rework
- Prevent tombstoning, bridging, wicking and exposed-pad voiding through pad, copper and paste design
- Design through-hole parts for wave, selective or pin-in-paste soldering and plan panels for handling
- Choose a test strategy, estimate its coverage and design test points, programming and boundary-scan access
- Lay out boards that can be reworked and repaired without collateral damage
Who it is for
- PCB designers who want fewer assembly defects and engineering queries on each new build
- Hardware engineers responsible for moving a board from prototype to volume assembly
- Test and manufacturing engineers who review layouts for assembly and test access
- Engineering leads who need to agree process routes and test strategies with assemblers
Syllabus
Module 1: Process Routes and Package Choice
How the layout decides the assembly sequence, and the assembly trade-offs of small passives, leadless and area-array packages and through-hole parts.
- Process Routes and the Cost of Each Step
- Small Passives: 0402, 0201 and 01005
- Leadless and Area-Array Packages: QFN, LGA and BGA
- Through-Hole Parts in an SMT Design
- Module quiz (5 questions)
Module 2: Spacing, Orientation and Polarity
Space parts for placement, inspection and rework, orient them for the process and the placement data, and mark polarity so it survives assembly.
- Spacing for Placement, Inspection and Rework
- Orientation for the Process and the Placement Data
- Polarity Marking That Survives Assembly
- Module quiz (5 questions)
Module 3: Defects That Design Can Prevent
The mechanisms behind tombstoning, skew, wicking, bridging, opens, head-in-pillow and exposed-pad voiding, and the pad, copper and paste design that prevents them.
- Tombstoning, Skew and Wicking
- Bridging, Opens and Head-in-Pillow
- Voiding Under Exposed Pads and Windowed Paste
- Module quiz (5 questions)
Module 4: Through-Hole Soldering and Panel Handling
Design through-hole parts for wave, selective and pin-in-paste soldering, and design the assembly panel as a fixture for the whole line.
- Designing Through-Hole Parts for Wave Soldering
- Selective Soldering and Pin-in-Paste
- Assembly Panels, Fiducials, Tooling and Handling
- Module quiz (5 questions)
Module 5: Design for Test and Repair
Choose a test strategy and judge its coverage, design test points to fixture rules, provide programming and boundary-scan access, and lay out boards that can be reworked.
- Choosing a Test Strategy and Judging Coverage
- Test Point Design in Depth
- Programming, Boundary Scan and Debug Access
- Designing for Rework and Repair
- Module quiz (5 questions)
Free downloads for this course
- PCB Layout Review Checklist (Checklist)
- PCB and PCBA Quote Request Checklist (Checklist)
- Bill of Materials (BOM) Template (Template)
Discuss your project
Email support@aavico.com or use Get in Touch when the website finishes loading.