EMC by Design: Grounding, Shielding and Layout
Design boards and products that pass emissions and immunity testing first time, by design rather than by rework.
Learn why products fail EMC tests and how to design so they do not. This course covers common-mode currents, noise sources, grounding and return paths, stackup and layout, filtering, cables and shielding, ESD protection and bench pre-compliance testing, with the physics behind every rule of thumb.
Intermediate · 5 modules · 18 lessons · free certificate
About this course
Most EMC failures are designed in long before the product reaches a test lab. A ground plane split in the wrong place, a clock routed along the board edge, a cable shield terminated with a length of wire or a filter placed a few centimetres from its connector can each turn a quiet circuit into an efficient transmitter. Fixing these problems late means ferrites clipped onto cables, copper tape and board respins. This course teaches the reasoning that lets you avoid them in the schematic and the layout.
The course starts with the physics: emissions and immunity, conducted and radiated coupling, and why small common-mode currents on cables usually dominate radiated emissions. It then works through noise sources, grounding and return paths, stackup and layout, filtering, cables and enclosures, and ESD and transient protection. The final module shows how to find problems at your own bench with near-field probes, a spectrum analyser and a LISN, and gives an overview of the main emissions and immunity standards. Numbers come from named standards and physical laws, or are labelled as typical.
The course does not cover the regulatory process itself: choosing harmonised standards, test reports, declarations of conformity and marking. Those are covered in Regulatory Compliance for Electronic Products. Radio transmitter design and safety approvals are also out of scope.
Before you start: You should be comfortable reading schematics and have laid out at least one multilayer board. Some familiarity with rise time, inductance and capacitance helps. PCB Layout Fundamentals: Placement and Routing and Signal Integrity Fundamentals in the AAVICO Academy cover useful background.
What you will learn
- Explain the difference between differential-mode and common-mode currents and estimate how each radiates
- Identify the main noise sources on a board and reduce them at the source with edge control and tight loops
- Plan grounding, return paths, chassis connections and a stackup that keep return currents under their signals
- Select and place ferrite beads, common-mode chokes, LC filters and TVS diodes where they actually work
- Terminate cable shields and design enclosure seams and apertures that preserve shielding
- Run bench pre-compliance scans with near-field probes, a current clamp, a spectrum analyser and a LISN
Who it is for
- Electronics engineers who lay out boards and want them to pass emissions and immunity testing first time
- Hardware designers who have had a product fail an EMC test and want to understand why
- Layout specialists who want the physics behind EMC layout rules rather than a checklist
- Engineering leads who plan pre-compliance testing and review designs before they go to a test lab
Syllabus
Module 1: EMC Fundamentals and Noise Sources
What EMC means, why common-mode currents dominate cable radiation, and where the noise on a board comes from.
- What EMC Means: Emissions, Immunity and Coupling
- Differential-Mode and Common-Mode Currents
- Switching Edges, Clocks and Harmonics
- Switching Regulators and Loop Area
- Module quiz (5 questions)
Module 2: Grounding and Return Paths
Where return current really flows, why one solid ground plane usually beats a split one, and how to connect to the chassis.
- Ground Is a Return Path, Not a Sink
- One Solid Ground Plane: When and Why Not to Split
- Chassis Ground, Its Connection and Stitching
- Module quiz (5 questions)
Module 3: Stackup and Layout for EMC
Choose reference planes and a stackup for EMC, place the board in zones and route fast signals where they cannot radiate.
- Reference Planes and Stackup Choices
- Placement and Zoning for EMC
- Routing Fast Signals for EMC
- Module quiz (5 questions)
Module 4: Filtering, Cables and Shielding
Choose and place ferrite beads, common-mode chokes and LC filters, terminate cable shields properly and keep enclosures shielding.
- Ferrite Beads and Their Limits
- Common-Mode Chokes, LC Filters and Placement
- Cables, Connectors and Shield Termination
- Enclosures, Apertures and Gaskets
- Module quiz (5 questions)
Module 5: ESD, Transients and Pre-compliance Testing
Protect interfaces against ESD and transients, find emissions problems at your own bench and understand the standards you will be tested to.
- ESD and Transient Protection
- Bench Pre-compliance: Probes and the Spectrum Analyser
- Conducted Emissions with a LISN
- The Standards Families and the Road to the Test Lab
- Module quiz (5 questions)
Free downloads for this course
- EMC Design Checklist (Checklist)
- Product Certification Planning Worksheet (Template)
Discuss your project
Email support@aavico.com or use Get in Touch when the website finishes loading.