Low-Power Design for Battery Devices
Budget, design, build and measure devices that run for years on a battery.
Make battery life a design result rather than a surprise. Build an energy budget, choose and derate the right battery, pick regulators and load switches that suit microamp loads, remove hidden leakage from hardware and firmware, and measure current correctly from sleep to radio peaks.
Intermediate · 5 modules · 18 lessons · free certificate
About this course
Battery life is decided by many small choices: a divider left across the battery, a regulator chosen for its full-load efficiency, a pin left floating, a radio retry loop, a meter that reads the wrong number. Each one looks harmless on its own, yet together they turn a five-year product into a one-year product. This course follows those choices in the order a design meets them, from the first spreadsheet budget to the final measured power profile.
You will learn to reason in charge per event, to derate battery capacity for load, temperature, pulses and self-discharge, to compare primary and rechargeable chemistries, and to understand the safety and transport rules that apply to lithium cells. Later modules cover charging and protection, power conversion at light load, low-leakage circuit design, firmware techniques and the instruments and methods that give trustworthy microamp readings. Figures are labelled as typical where they vary between parts and suppliers, and should be checked against datasheets.
Sleep modes and the basic wake-work-sleep pattern are covered in Embedded Firmware Fundamentals, and this course builds on them rather than repeating them. Detailed regulator design belongs to Power Supply Design for PCBs, and radio protocols to Wireless Connectivity for IoT. Battery pack engineering for large packs, battery certification testing itself and legal advice on shipping dangerous goods are out of scope.
Before you start: Comfort with Ohm's law, reading component datasheets and basic microcontroller concepts. You should know what sleep modes are and how firmware enters them; the sleep modes lesson in Embedded Firmware Fundamentals covers that background.
What you will learn
- Build an energy budget from duty cycles and turn it into a realistic, derated battery life estimate
- Choose a battery chemistry for a load profile and temperature range, and recognise coin cell and pulse limits
- Specify charging, protection, fuel gauging and power conversion that suit microamp sleep currents
- Find and remove leakage paths in circuits, GPIO configuration and peripheral power control
- Apply firmware techniques such as wake source selection, clock choice, DMA and radio scheduling
- Measure current across a wide dynamic range and build a power profile you can trust
Who it is for
- Hardware engineers designing sensors, wearables, trackers and other battery-powered products
- Firmware engineers who own power consumption and want to understand the hardware side
- Product and test engineers who must predict, verify and defend a battery life claim
- Makers and students moving from mains-powered prototypes to devices that run for years
Syllabus
Module 1: The Energy Budget
Turn states and duty cycles into an average current, a derated battery life and an understanding of why the sleep floor usually wins.
- Average Current from Duty Cycles
- Worked Battery-Life Calculations
- Why Sleep Current Often Dominates
- Module quiz (5 questions)
Module 2: Batteries for Low-Power Products
Compare primary and rechargeable chemistries, understand how load, temperature and pulses change capacity, and respect the safety and transport rules for lithium cells.
- Primary Cells: Alkaline and Lithium Chemistries
- Capacity Versus Load, Temperature and Pulses
- Rechargeable Cells and Self-Discharge
- Battery Safety and Transport Rules
- Module quiz (5 questions)
Module 3: Charging, Protection and Power Conversion
Charge and protect lithium cells correctly, gauge what is left, and choose regulators, load switches and harvesters that behave well at microamp loads.
- Charging Lithium Cells: CC/CV and Beyond
- Protection Circuits and Fuel Gauging
- Regulators at Light Load
- Load Switches, Power Gating and Energy Harvesting
- Module quiz (5 questions)
Module 4: Low-Leakage Hardware and Low-Power Firmware
Remove leakage from resistor networks, inputs, GPIO states, peripherals and capacitors, then apply firmware techniques that keep the core and radio asleep as long as possible.
- Pull-ups, Dividers and Floating Inputs
- GPIO States, Peripheral Power and Hidden Leakage
- Firmware: Choosing Sleep Modes, Wake Sources and Clocks
- Firmware: Duty Cycling, DMA, Radios and Avoiding Polling
- Module quiz (5 questions)
Module 5: Measuring Current and Building a Power Profile
Measure from sub-microamp sleep to radio peaks without disturbing the device, choose suitable instruments, and turn measurements into a power profile that validates the budget.
- Shunts, Burden Voltage and Dynamic Range
- Instruments for Low-Power Measurement
- Measuring Sleep Current and Building a Power Profile
- Module quiz (5 questions)
Discuss your project
Email support@aavico.com or use Get in Touch when the website finishes loading.