Analogue and Mixed-Signal Board Design
Get the resolution you paid for: noise, op-amps, converters, grounding and precision layout on real boards.
Design boards where precision analogue circuits and converters share space with digital logic and still meet their noise and accuracy targets. Covers noise budgets, op-amp realities, ADC and DAC interfacing, grounding and partitioning, precision layout, analogue power and worked sensor front-ends.
Advanced · 5 modules · 18 lessons · free certificate
About this course
A 24-bit converter on a datasheet and 24 useful bits on a board are very different things. Between them sit resistor noise, op-amp offsets and limits, a driver that cannot settle, an anti-alias filter that was never calculated, a noisy reference, a jittery sample clock, return currents flowing through the wrong copper, thermocouple junctions nobody noticed and a switching regulator whose ripple passes straight through the analogue supply. This course teaches you to find and control each of these, with the physics and the arithmetic that let you predict performance before the board is built.
The course starts with noise fundamentals and a working noise budget, then covers op-amp circuits as they behave on a board, ADC and DAC interfacing, grounding and partitioning for mixed-signal boards, precision layout and power for analogue circuits. It finishes with worked bridge, thermocouple and current-sense front-ends and a module on measuring noise so you can verify what you designed. Numbers come from physical laws and standard definitions, or are labelled as typical.
General EMC design, shielding and compliance testing are covered in EMC by Design: Grounding, Shielding and Layout. Regulator topologies, switching converter design and power-stage layout are covered in Power Supply Design for PCBs. RF design, integrated circuit design and the internal design of converters are out of scope.
Before you start: You should be comfortable with op-amp basics, decibels, RC filters and reading converter datasheets, and have laid out at least one multilayer board. Signal Integrity Fundamentals and Power Supply Design for PCBs in the AAVICO Academy cover useful background.
What you will learn
- Build a noise budget from thermal, shot and 1/f noise, integrate it over the right bandwidth and predict SNR and ENOB
- Choose and lay out op-amp circuits that respect offset, bias current, input and output limits and stability with capacitive loads
- Drive SAR and delta-sigma converters correctly, including the input RC, anti-alias filter, reference and sample clock
- Plan grounding and partitioning for a mixed-signal board and interpret AGND and DGND advice in converter datasheets
- Lay out precision circuits that control thermal EMFs, leakage, heat and current-sense errors, and power them cleanly
- Measure the noise and accuracy of a finished front-end and compare it with the prediction
Who it is for
- Hardware engineers designing boards with precision sensors, ADCs or DACs alongside microcontrollers and switching regulators
- Layout engineers who want the reasoning behind analogue grounding, guarding and placement rules
- Digital or firmware engineers who have inherited an analogue front-end that is noisier than its datasheets promise
- Engineering leads reviewing mixed-signal designs before layout release
Syllabus
Module 1: Noise Fundamentals and the Noise Budget
Where noise comes from, how to integrate it over bandwidth, and how it sets SNR and ENOB.
- Thermal, Shot and 1/f Noise
- Noise Density, Noise Bandwidth and Integration
- SNR, ENOB and the Noise Budget
- Module quiz (5 questions)
Module 2: Op-Amp Circuits on a Real Board
DC errors, input and output limits, capacitive-load stability and the layout of the feedback network.
- DC Errors: Offset, Bias Current and Drift
- Input and Output Limits: Rail-to-Rail Realities
- Stability with Capacitive Loads
- Feedback Layout, Leakage and Guarding
- Module quiz (5 questions)
Module 3: ADC and DAC Interfacing
Converter architectures, driving the input, anti-alias filtering, references and sample-clock jitter.
- SAR and Delta-Sigma Converters
- Driving the ADC Input and Charge Kickback
- Anti-Alias Filtering
- References, Clocks and Jitter
- Module quiz (5 questions)
Module 4: Grounding, Partitioning and Precision Layout
Where return currents flow, how to partition a mixed-signal board, AGND and DGND pins, and thermal and mechanical effects on precision circuits.
- Return Currents and the Single Solid Ground
- AGND, DGND, Split Grounds and Star Points
- Precision Layout: Thermal EMFs, Heat and Stress
- Module quiz (5 questions)
Module 5: Analogue Power, Sensor Front-Ends and Verification
Clean supplies for analogue circuits, worked bridge, thermocouple and current-sense front-ends, and measuring noise on the finished board.
- Power for Analogue: Post-Regulation and PSRR
- Worked Front-End: A Bridge Sensor
- Worked Front-Ends: Thermocouple and Current Sense
- Measuring Noise and Verifying Performance
- Module quiz (5 questions)
Discuss your project
Email support@aavico.com or use Get in Touch when the website finishes loading.