Ceramic Capacitors: X7R, X5R, C0G and the Capacitance You Actually Get
Multilayer ceramic capacitors are the most numerous components on most boards, used for decoupling, filtering and timing. Their marked capacitance is a nominal figure. The dielectric material determines how the value changes with temperature, and for the high-density types, how much is lost when a DC voltage is applied. Choosing the dielectric and case size with this in mind is the difference between a supply that is stable and one that only looks so on the schematic.
At a glance
- ±15%
- Capacitance change of X7R and X5R dielectrics across their temperature range.
- 125 °C
- Upper temperature limit of X7R. X5R is rated to 85 °C.
- ±30 ppm/°C
- Temperature coefficient of C0G (NP0), the most stable common dielectric.
- 100 nF
- The customary decoupling value placed at each supply pin.
The problem
High-capacitance ceramics lose capacitance as DC voltage is applied. A capacitor operated near its rated voltage can deliver well under half its marked value, and the loss is greater in smaller packages. This does not appear in the temperature code; it has to be read from the manufacturer’s curves.
Decoupling also fails for layout reasons. A capacitor placed far from the pin it serves, or connected through long traces, adds inductance that makes it ineffective at the frequencies where it is needed.
Read the DC-bias curve, not just the label. The capacitance in your circuit is the one at your operating voltage.
Reading the code
The three-character code describes temperature behaviour. In X7R, X means a lower limit of -55 °C, 7 an upper limit of +125 °C, and R a change of ±15% over that range. X5R is the same with an upper limit of +85 °C.
C0G, also called NP0, is a different class of dielectric. Its capacitance barely changes with temperature, voltage or age, which makes it the choice for timing, filters and anything needing a precise value, though it is only available in small capacitances.
What good looks like
Use C0G for precision and timing, X7R for general decoupling and filtering, and X5R where high capacitance in a small package is essential.
Check the DC-bias curve at your operating voltage and choose a higher voltage rating or a larger case if too little capacitance remains.
Place decoupling capacitors as close as possible to the pins they serve, with short connections to power and ground planes.
| Dielectric | Temperature range | Change over range | Typical use |
|---|---|---|---|
| C0G (NP0) | -55 to +125 °C | ±30 ppm/°C | Timing, filters, precision |
| X7R | -55 to +125 °C | ±15% | General decoupling and filtering |
| X5R | -55 to +85 °C | ±15% | High capacitance in small packages |
| Y5V | -30 to +85 °C | +22% / -82% | Non-critical bulk; avoid for stable values |
| C0G (NP0) | X7R | |
|---|---|---|
| Stability with temperature | Excellent | Moderate |
| Loss under DC bias | Negligible | Significant |
| Capacitance available | Small | Large |
| Cost per microfarad | High | Low |
What it changes
Stable Supplies
Regulators and devices see the capacitance the design assumed.
Predictable Filters
Precision circuits use a dielectric whose value does not wander.
Reliability
Parts are operated within their voltage and temperature ratings.
Fewer Mysteries
Intermittent faults caused by marginal decoupling are designed out.
Where to go next
Ceramic capacitors can crack when a board flexes. Keep large parts away from board edges, mounting holes and breakaway tabs.
Some high-capacitance ceramics are piezoelectric and can produce audible noise or inject noise into sensitive circuits. Consider other types there.
Problems this prevents
- Capacitance lost to DC bias
- X5R parts used above 85 °C
- Decoupling capacitors placed far from their pins
- Cracked capacitors near board edges
Discuss your project
Email support@aavico.com or use Get in Touch when the website finishes loading.