Component Package Sizes: 0402, 0603, 0805 and What to Choose
Passive components are named by their dimensions. An 0603 resistor is 0.06 by 0.03 inches; the same part in metric notation is a 1608, for 1.6 by 0.8 mm. The size you choose affects how much the board holds, how easily it is assembled and inspected, and what power and voltage the part can handle. This article sets out the dimensions and the trade-offs.
At a glance
- 0603
- A good general-purpose default: compact, easy to place and reworkable by hand.
- 1.6 x 0.8 mm
- The actual size of an 0603 package, called 1608 in metric notation.
- 0402
- Well under half the body area of an 0603; standard for dense designs.
- 0.1 W
- A typical power rating for an 0603 resistor. Smaller packages dissipate less.
The problem
Choosing the smallest package everywhere saves area but has costs. Smaller parts dissipate less power, ceramic capacitors lose more capacitance under DC bias in small case sizes, and anything below 0402 is difficult to rework without specialist equipment.
The two naming systems cause real errors. An imperial 0603 and a metric 0603 are different parts, the metric one being far smaller, and a bill of materials that does not say which is meant will eventually be built wrong.
Pick one package size as the default for the whole board and depart from it only for a reason you can state.
Choosing a default
Use 0603 where space allows: it is cheap, widely stocked and easy to inspect. Move to 0402 when density requires it. Reserve 0201 and smaller for designs that cannot be built any other way, and confirm that your assembler handles them.
Check ratings, not just dimensions. Power dissipation, working voltage and, for capacitors, the capacitance remaining under bias all fall with package size.
What good looks like
Choose a default size for resistors and capacitors based on board density and how the product will be assembled and serviced.
For each part, check power, voltage and capacitor DC-bias behaviour in that package rather than assuming.
State the size system on the bill of materials and use manufacturer part numbers so there is no ambiguity.
| Imperial | Metric | Size (mm) | Typical power |
|---|---|---|---|
| 0201 | 0603 | 0.6 x 0.3 | 0.05 W |
| 0402 | 1005 | 1.0 x 0.5 | 0.063 W |
| 0603 | 1608 | 1.6 x 0.8 | 0.1 W |
| 0805 | 2012 | 2.0 x 1.25 | 0.125 W |
| 1206 | 3216 | 3.2 x 1.6 | 0.25 W |
| mm² | |
|---|---|
| 0201 | 0.18 |
| 0402 | 0.5 |
| 0603 | 1.28 |
| 0805 | 2.5 |
| 1206 | 5.12 |
What it changes
Assembly Yield
Sizes within the assembler’s comfortable range place and solder consistently.
Serviceability
Parts that can be reworked by hand make prototypes and repairs far quicker.
Sourcing
Common sizes are stocked widely and have many second sources.
Performance
Ratings checked per package avoid overheated resistors and under-value capacitors.
Where to go next
Standardise values as well as sizes. A design that uses twelve resistor values instead of thirty is cheaper to buy and to load onto a placement machine.
For larger integrated circuits, weigh QFN against QFP and BGA in the same way: area against ease of inspection and rework.
Problems this prevents
- Imperial and metric size codes confused
- Parts too small to rework during development
- Capacitors that lose most of their value under bias
- Resistors running beyond their power rating
Discuss your project
Email support@aavico.com or use Get in Touch when the website finishes loading.