ESD Protection: Designing to Pass IEC 61000-4-2

A person walking across a carpet can carry several kilovolts, and touching a product releases that charge in a pulse with a rise time under a nanosecond. IEC 61000-4-2 defines how products are tested for immunity to these discharges, and most EMC product standards call it up. Failures range from a momentary reset to permanent damage. This article explains the test, its levels, and the design choices that let a product pass.

At a glance

8 kV
The highest standard contact discharge level, level 4 in IEC 61000-4-2.
15 kV
The highest standard air discharge level, also level 4.
0.8 ns
The nominal rise time of the discharge current, which makes ESD a high-frequency event.
150 pF
With 330 Ω, the discharge network that models a person holding a metal object.

The problem

The discharge current peaks at several amps to tens of amps within a nanosecond. Its fast edge makes every trace and cable a potential antenna, so an ESD event can upset circuits far from the point of contact as well as damaging the input it hits.

IC datasheets often quote an ESD rating, but this is usually a component-level human body model figure intended for safe handling in a factory. It does not mean the pin will survive a system-level IEC 61000-4-2 discharge, which delivers far more current.

Decide where the ESD current will go before it arrives, and make that path shorter than any path through your circuit.

Designing the current path

Place a TVS diode or ESD protection array at the connector, before the signal reaches anything else, with the shortest possible connection to ground or chassis. At these edge rates the connection develops tens of volts per nanohenry, so the protector must sit right at the entry point with a via straight to the plane.

Keep protected and unprotected traces apart, add series resistance or filtering on sensitive inputs where the signal allows, and bond metal enclosures and connector shells with low impedance. In plastic enclosures, gaps around seams and buttons decide where discharges can enter.

What good looks like

Find the required levels and performance criterion in your product standard; CISPR 35 for multimedia equipment, for example, specifies 4 kV contact and 8 kV air.

Protect each exposed interface at the connector with a device rated for the level and suited to the signal, and plan its ground path.

Test prototypes with an ESD generator at every touch point in both polarities, and fix weaknesses before formal testing.

IEC 61000-4-2 test levels
LevelContact dischargeFirst peak currentAir discharge
12 kV7.5 A2 kV
24 kV15 A4 kV
36 kV22.5 A8 kV
48 kV30 A15 kV
Test levels and first peak current of the contact discharge, from IEC 61000-4-2. Product standards set the level required.
First peak current by contact level
A
2 kV7.5
4 kV15
6 kV22.5
8 kV30
Nominal first peak of the contact discharge current, 3.75 A per kilovolt, with a 0.8 ns rise time.

What it changes

Compliance

The product passes the immunity tests its standard requires.

Field Robustness

Fewer resets and failures from everyday static.

Lower Returns

Damaged interfaces stop being a source of failed units.

Faster Approval

Problems found on prototypes are fixed before the lab.

Where to go next

Firmware matters too. A watchdog and robust recovery can turn a lock-up into a brief, self-clearing glitch, which may meet a less strict performance criterion.

Choose low-capacitance protection devices for high-speed interfaces such as USB and HDMI, so the protection does not degrade the signal.

Problems this prevents

  • Connectors with no protection at the entry point
  • Long ground paths from the protection device
  • Relying on IC datasheet ESD ratings
  • Lock-ups that need a power cycle to clear

Discuss your project

Email support@aavico.com or use Get in Touch when the website finishes loading.