Environmental Testing: Temperature, Humidity, Vibration and Shock

A product’s real environment is rarely a laboratory bench at room temperature. It may sit in a vehicle that freezes overnight and bakes in the afternoon, in a humid plant room, or on a machine that vibrates for its whole life. Environmental testing reproduces those conditions in a controlled way, using established test methods, to find weaknesses while they can still be designed out. This article explains the main tests and the standards that define them.

At a glance

IEC 60068
The international series of environmental test methods used for most electronic products.
MIL-STD-810
The US defence standard of environmental test methods, also widely used outside defence.
85/85
A common humidity stress test for components: 85 °C and 85% relative humidity, from JEDEC JESD22-A101.
-40 °C
The low limit of the industrial temperature range used for many components.

The problem

Each environment attacks a different weakness. Temperature changes stress solder joints and connectors through mismatched expansion; humidity drives corrosion and leakage on contaminated boards; vibration fatigues heavy components, cables and their joints; shock cracks ceramic capacitors and dislodges parts.

Few of these failures appear in a functional test at room temperature. They show up after weeks or months in the field, when they are expensive to diagnose and fix.

Test the product in the environment it will live in, not the one it was designed in.

Choosing test levels

Start from the environment in the requirements: operating and storage temperature, humidity, vibration sources and handling. Then select the corresponding test methods and severities from the relevant standard. Industry and product standards often specify them directly, for example for automotive, railway or medical equipment.

Test the product operating where the requirement says it must operate, and monitor it throughout, because some faults are intermittent and appear only at temperature or during vibration. A functional check afterwards may miss them entirely.

What good looks like

Define the product’s environments from its requirements, including transport and storage, and map each to a test method and severity.

Run early, informal tests on prototypes, such as a temperature sweep in a chamber, to find weaknesses before formal testing.

Perform formal tests on design-representative units with continuous monitoring, and record every anomaly with its conditions.

Common environmental tests
EnvironmentIEC 60068 partMIL-STD-810Typical weakness found
Cold2-1Method 502Start-up, battery and display behaviour
Dry heat2-2Method 501Overheating, material softening
Change of temperature2-14Method 503Solder joint and connector fatigue
Damp heat2-78, 2-30Method 507Corrosion, leakage, condensation
Vibration2-6, 2-64Method 514Fatigue of joints, cables, heavy parts
Shock2-27Method 516Cracked parts, dislodged connectors
Test method references from the IEC 60068-2 series and MIL-STD-810H. Severities come from the product requirements or product standards.
Width of component temperature grades
°C
Commercial70
Industrial125
Automotive Grade 1165
Military180
Span of common ambient operating ranges: commercial 0 to 70 °C, industrial -40 to 85 °C, AEC-Q100 Grade 1 -40 to 125 °C, military -55 to 125 °C. Check each datasheet.

What it changes

Field Reliability

Weaknesses are found and fixed before shipment.

Defined Margins

The product’s limits are known, not assumed.

Customer Confidence

Test reports show performance against recognised methods.

Fewer Returns

Environmental failures are caught in the laboratory, not by users.

Where to go next

Check that every component is rated for the full temperature range, including electrolytic capacitors, batteries, displays and connectors, which often have narrower ranges than the ICs.

Accelerated methods such as highly accelerated life testing find weaknesses quickly, but they find limits rather than demonstrate compliance.

Problems this prevents

  • Solder joints cracking after temperature cycling
  • Corrosion from humidity on unprotected boards
  • Heavy parts failing under vibration
  • Components rated for a narrower range than the product

Discuss your project

Email support@aavico.com or use Get in Touch when the website finishes loading.