USB-C Power: From 5 V to 240 W
USB-C has become the default power input for new products, replacing barrel jacks and proprietary chargers. The connector itself does not guarantee any particular power level. A device signals what it is with resistors on the configuration channel pins and, if it needs more than the basic level, negotiates a voltage and current using the Power Delivery protocol. This article sets out the levels available and the minimum a design needs to get right.
At a glance
- 5.1 kΩ
- The pull-down resistor on each CC pin that identifies a device as a power sink.
- 15 W
- Maximum without Power Delivery: 5 V at 3 A, advertised by the source.
- 100 W
- Maximum of the standard power range: 20 V at 5 A.
- 240 W
- Maximum of the extended power range added in USB PD 3.1: 48 V at 5 A.
The problem
The most common USB-C design error is omitting the CC pull-down resistors, or sharing a single resistor between both CC pins. The product then works with an old-style adapter cable and draws nothing from a proper USB-C charger, which will not enable its output.
Assuming power is also risky. A source may offer only the default current, and a design that draws 3 A without checking what was advertised can overload it.
Two 5.1 kΩ resistors, one per CC pin. Leaving them out is the reason many USB-C products do not charge.
How much can you draw
Without Power Delivery, the source advertises its capability through the pull-up on the CC line, and the sink reads it: default USB power, 1.5 A or 3 A at 5 V. A simple design can stop there and have up to 15 W.
For more, a Power Delivery controller negotiates a higher voltage. Fixed levels of 9, 15 and 20 V are standard, with up to 5 A available at 20 V only through an electronically marked cable.
What good looks like
Decide the power the product needs and whether 5 V at up to 3 A is enough or Power Delivery is required.
Fit a 5.1 kΩ pull-down on each CC pin for a sink, and add a PD controller if higher voltages are needed.
Read the advertised current before drawing it, and protect the input against the highest voltage the port could present.
| Mode | Voltage | Current | Power |
|---|---|---|---|
| Default USB 2.0 | 5 V | 0.5 A | 2.5 W |
| Type-C 1.5 A | 5 V | 1.5 A | 7.5 W |
| Type-C 3 A | 5 V | 3 A | 15 W |
| PD standard range | Up to 20 V | Up to 5 A | 100 W |
| PD 3.1 extended range | Up to 48 V | 5 A | 240 W |
| W | |
|---|---|
| USB 2.0 default | 2.5 |
| Type-C 1.5 A | 7.5 |
| Type-C 3 A | 15 |
| PD standard | 100 |
| PD 3.1 extended | 240 |
What it changes
Works With Any Charger
Correct configuration means compliant sources enable their output.
Right Power Level
The product draws what the source offers and no more.
One Connector
Power and data share a single, reversible, widely available port.
Robust Input
Protection sized for negotiated voltages survives faulty cables and chargers.
Where to go next
Higher currents and voltages need cables rated for them. Above 3 A, an electronically marked cable is required.
If the product also uses USB data, follow the layout rules for the 90 Ω differential pairs and fit protection close to the connector.
Problems this prevents
- Missing or shared CC pull-down resistors
- Drawing more than the source advertised
- An input unprotected against 20 V
- Assuming every cable carries 5 A
Discuss your project
Email support@aavico.com or use Get in Touch when the website finishes loading.