{"docs":[{"id":134,"title":"Board Bring-Up: A First-Power Checklist for New Hardware","heading":"Board Bring-Up: A First-Power Checklist for New Hardware","subheading":null,"category":"Prototyping","body":{"root":{"type":"root","children":[{"type":"heading","tag":"h3","version":1,"children":[{"type":"text","text":"The sequence that works","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"Start unpowered: inspect under magnification for orientation, bridges and missing parts, then measure resistance from each rail to ground and compare it with the expected value or a known-good board. A very low reading usually means a short, though large capacitances read low briefly while the meter charges them.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"Then apply power through a current-limited supply, starting low, and watch the current as you raise it. Check every rail voltage, then clocks and reset lines, then connect the debugger and confirm the processor responds before loading application firmware and testing each interface in turn.","version":1}]}],"direction":"ltr","format":"","indent":0,"version":1}},"tags":"Prototyping, Bring-Up, Hardware Debug","cardCta":{"label":null,"link":null},"pageCta":{"label":"Talk to AAVICO engineering","link":"/contact"},"excerpt":"The first power-up of a new board is where assembly faults and design errors meet. A methodical bring-up finds them without destroying the evidence or the board.","featuredImage":null,"type":"Blog","readTime":"3 min read","publishedAt":"2026-11-15T21:29:00.000Z","heroImage":null,"introText":"A new board straight from assembly has never been powered. It may have a short, a part fitted the wrong way round, or a design error that sends the wrong voltage to an expensive chip. Connecting it to a full supply and hoping risks damaging the one prototype that would have shown the problem. A methodical bring-up checks the board step by step, from passive measurements to running firmware. This article sets out that sequence.","metrics":[{"id":"board-bring-up-a-first-power-checklist-for-new-h-metric-1","value":"Ohms first","label":"Measure each rail to ground before power is applied, to find shorts safely.","icon":null},{"id":"board-bring-up-a-first-power-checklist-for-new-h-metric-2","value":"Limit amps","label":"Use a bench supply with its current limit set just above the expected draw.","icon":null},{"id":"board-bring-up-a-first-power-checklist-for-new-h-metric-3","value":"One rail","label":"Bring up power in stages where the design allows, checking each before the next.","icon":null},{"id":"board-bring-up-a-first-power-checklist-for-new-h-metric-4","value":"Log it","label":"Record every measurement, so later boards can be compared with the first.","icon":null}],"gallery":[],"challenge":{"root":{"type":"root","children":[{"type":"paragraph","version":1,"children":[{"type":"text","text":"An assembly fault such as a solder bridge or a reversed diode can draw enough current to damage traces and parts in a moment if the supply is unlimited. Worse, the damage often destroys the evidence of what went wrong.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"Design errors are equally possible on a first board: a regulator set to the wrong output, a missing pull-up that holds a chip in reset, or a sequencing problem between rails. Each is easy to diagnose in isolation and hard to untangle if everything is powered at once.","version":1}]}],"direction":"ltr","format":"","indent":0,"version":1}},"blockquote":{"quote":"Measure before you power, limit before you switch on, and change one thing at a time.","author":"","role":"AAVICO Engineering"},"supportImage1":null,"deliverables":{"root":{"type":"root","children":[{"type":"paragraph","version":1,"children":[{"type":"text","text":"Prepare a bring-up plan listing every rail with its expected voltage, resistance to ground and current, and every clock and reset signal to check.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"Work through it on the first board with current limiting, a check for hot components at each step, and a written log.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"Record fixes and rework on the board and in the design files, then repeat a shorter sequence on later boards.","version":1}]}],"direction":"ltr","format":"","indent":0,"version":1}},"results":[{"id":"board-bring-up-a-first-power-checklist-for-new-h-result-1","title":"Protected Prototypes","description":"Faults are found before they cause damage."},{"id":"board-bring-up-a-first-power-checklist-for-new-h-result-2","title":"Faster Diagnosis","description":"Each stage isolates problems to a small part of the circuit."},{"id":"board-bring-up-a-first-power-checklist-for-new-h-result-3","title":"Design Feedback","description":"Errors are recorded and fixed in the next revision."},{"id":"board-bring-up-a-first-power-checklist-for-new-h-result-4","title":"Repeatable Process","description":"Later boards are brought up quickly from the same plan."}],"lookingAhead":{"root":{"type":"root","children":[{"type":"paragraph","version":1,"children":[{"type":"text","text":"Design for bring-up: test points on every rail, links to isolate rails and an accessible debug header make this far easier.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"Write simple test firmware that exercises each interface on its own. It separates hardware faults from application software problems.","version":1}]}],"direction":"ltr","format":"","indent":0,"version":1}},"supportImage2":null,"testimonial":{"quote":null,"author":null,"role":null,"photo":null},"challengesSolved":[{"id":"board-bring-up-a-first-power-checklist-for-new-h-challenge-1","title":"Prototypes damaged by an unlimited supply","description":null,"icon":null},{"id":"board-bring-up-a-first-power-checklist-for-new-h-challenge-2","title":"Evidence of a fault burnt away at first power","description":null,"icon":null},{"id":"board-bring-up-a-first-power-checklist-for-new-h-challenge-3","title":"Chips powered before rail voltages were checked","description":null,"icon":null},{"id":"board-bring-up-a-first-power-checklist-for-new-h-challenge-4","title":"Prototype fixes not carried into the design","description":null,"icon":null}],"relatedPosts":[],"contactUs":{"show":true},"updatedAt":"2026-11-15T17:32:32.682Z","createdAt":"2026-11-15T17:32:32.682Z"}],"hasNextPage":false,"hasPrevPage":false,"limit":10,"nextPage":null,"page":1,"pagingCounter":1,"prevPage":null,"totalDocs":1,"totalPages":1}