{"docs":[{"id":102,"title":"Controlled Impedance: 50, 90 and 100 Ohm Explained","heading":"Controlled Impedance: 50, 90 and 100 Ohm Explained","subheading":null,"category":"PCB Design","body":{"root":{"type":"root","children":[{"type":"heading","tag":"h3","version":1,"children":[{"type":"text","text":"What moves impedance","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"A wider trace or a thinner dielectric lowers impedance; a narrower trace or thicker dielectric raises it. For differential pairs, moving the two traces closer together lowers the differential impedance.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"Keep the reference plane unbroken under the whole route. A trace crossing a split in the plane sees a jump in impedance and a much larger return loop, which is a common source of emissions failures.","version":1}]}],"direction":"ltr","format":"","indent":0,"version":1}},"tags":"PCB Design, Signal Integrity, High-Speed","cardCta":{"label":null,"link":null},"pageCta":{"label":"Talk to AAVICO engineering","link":"/contact"},"excerpt":"USB, Ethernet and RF traces only work if the board presents the impedance the standard expects. These are the targets and what sets them.","featuredImage":null,"type":"Blog","readTime":"3 min read","publishedAt":"2026-11-14T18:58:00.000Z","heroImage":null,"introText":"At high edge rates a PCB trace stops behaving like a wire and starts behaving like a transmission line. If its impedance does not match the driver and the load, part of every edge reflects, and the result is ringing, eye closure and failed compliance tests. Controlled impedance means designing and building the trace to a specified value. This article covers the common targets and the geometry that produces them.","metrics":[{"id":"controlled-impedance-50-90-and-100-ohm-e-metric-1","value":"50 Ω","label":"The single-ended standard for RF and most high-speed single-ended signals.","icon":null},{"id":"controlled-impedance-50-90-and-100-ohm-e-metric-2","value":"90 Ω","label":"Differential impedance required for USB 2.0 and USB 3.x pairs.","icon":null},{"id":"controlled-impedance-50-90-and-100-ohm-e-metric-3","value":"100 Ω","label":"Differential impedance for Ethernet, LVDS, HDMI and most other pairs.","icon":null},{"id":"controlled-impedance-50-90-and-100-ohm-e-metric-4","value":"±10%","label":"The usual manufacturing tolerance for controlled-impedance traces.","icon":null}],"gallery":[],"challenge":{"root":{"type":"root","children":[{"type":"paragraph","version":1,"children":[{"type":"text","text":"Impedance depends on trace width, the distance to the reference plane, the copper thickness and the dielectric constant of the laminate. Change any one and the impedance moves. A trace width copied from another board is wrong unless the stackup is identical.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"The dielectric constant of standard FR-4 is not a single number either. It varies with the resin content of the specific prepreg and with frequency, which is why the fabricator, who knows the materials, should confirm the final geometry.","version":1}]}],"direction":"ltr","format":"","indent":0,"version":1}},"blockquote":{"quote":"An impedance target without a stackup is a wish. The two have to be specified together.","author":null,"role":"AAVICO Engineering"},"supportImage1":null,"deliverables":{"root":{"type":"root","children":[{"type":"paragraph","version":1,"children":[{"type":"text","text":"Identify every net with an impedance requirement from the interface standards and device datasheets, and record the target and tolerance.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"Calculate trace geometry for your stackup with a field-solver tool, then send the targets to the fabricator and use the widths they confirm.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"Add the impedance table to the fabrication drawing and request test coupons if the design needs measured evidence.","version":1}]}],"direction":"ltr","format":"","indent":0,"version":1}},"results":[{"id":"controlled-impedance-50-90-and-100-ohm-e-result-1","title":"Signal Quality","description":"Matched traces deliver clean edges, which is what interface compliance testing measures."},{"id":"controlled-impedance-50-90-and-100-ohm-e-result-2","title":"First-Pass Success","description":"Impedance agreed with the fabricator before layout avoids a respin for a parameter that could not be met."},{"id":"controlled-impedance-50-90-and-100-ohm-e-result-3","title":"EMC","description":"Unbroken reference planes keep return currents under their signals and loops small."},{"id":"controlled-impedance-50-90-and-100-ohm-e-result-4","title":"Repeatability","description":"A documented impedance table makes every later build match the first."}],"lookingAhead":{"root":{"type":"root","children":[{"type":"paragraph","version":1,"children":[{"type":"text","text":"For lengths that are a small fraction of the signal wavelength, impedance control matters much less. Short, slow traces do not need it.","version":1}]},{"type":"paragraph","version":1,"children":[{"type":"text","text":"For radio traces, also follow the reference layout from the module or chip vendor closely. Antenna matching depends on more than the trace impedance.","version":1}]}],"direction":"ltr","format":"","indent":0,"version":1}},"supportImage2":null,"testimonial":{"quote":null,"author":null,"role":null,"photo":null},"challengesSolved":[{"id":"controlled-impedance-50-90-and-100-ohm-e-challenge-1","title":"Trace widths copied from a different stackup","description":null,"icon":null},{"id":"controlled-impedance-50-90-and-100-ohm-e-challenge-2","title":"High-speed routes crossing plane splits","description":null,"icon":null},{"id":"controlled-impedance-50-90-and-100-ohm-e-challenge-3","title":"Impedance left off the fabrication drawing","description":null,"icon":null},{"id":"controlled-impedance-50-90-and-100-ohm-e-challenge-4","title":"Compliance failures found only at the test lab","description":null,"icon":null}],"relatedPosts":[],"contactUs":{"show":true},"updatedAt":"2026-11-14T17:38:33.345Z","createdAt":"2026-11-14T17:38:33.345Z"}],"hasNextPage":false,"hasPrevPage":false,"limit":10,"nextPage":null,"page":1,"pagingCounter":1,"prevPage":null,"totalDocs":1,"totalPages":1}