Power Integrity and PDN Design
Design, simulate and measure power distribution networks that hold their voltage under fast loads.
Design power distribution networks that keep fast processors, FPGAs and SoCs inside their voltage limits. Learn target impedance, real capacitor behaviour, mounting inductance, planes and anti-resonance, DC drop and remote sense, ground bounce, and how to simulate and measure a PDN with worked numerical examples.
Advanced · 5 modules · 16 lessons · free certificate
About this course
Modern digital silicon draws large currents that change in nanoseconds, at supply voltages below a volt where the allowed ripple is a few tens of millivolts. Keeping that voltage steady is the job of the power distribution network: the regulator, the bulk and ceramic capacitors, the planes and vias, and the package and die. This course treats the PDN as one impedance seen by the silicon, explains which part is responsible for which frequency band, and shows how to design each part with numbers rather than folklore.
You will work through target impedance and its limits, the parasitics of real capacitors including DC bias derating, mounting and spreading inductance, plane capacitance, anti-resonance, DC voltage drop and via current, remote sense, ground bounce and simultaneous switching noise. The final module covers PDN simulation, impedance measurement with a vector network analyser and the two-port shunt-through method, and how to probe ripple without measuring your own probe. Every formula is given in plain text with a worked example, and typical values are labelled as such.
Out of scope: the design of the switching regulator itself and its control loop (see Power Supply Design for PCBs), transmission lines and crosstalk (see Signal Integrity Fundamentals), and on-chip power grid design. The course assumes you can already plan a stackup and lay out a multilayer board.
Before you start: You should be comfortable with complex impedance, inductance and capacitance, and with multilayer PCB layout and stackups. PCB Stackup Design and Signal Integrity Fundamentals in the AAVICO Academy cover useful background.
What you will learn
- Calculate a target impedance, state its assumptions and judge when a flat target is not enough
- Predict the impedance of real capacitors, including ESR, ESL, mounting inductance and DC bias derating
- Choose capacitor values, quantities and placement that avoid harmful anti-resonance peaks
- Size planes and vias for DC drop and current, and apply remote sense correctly
- Estimate ground bounce and simultaneous switching noise and reduce it in layout and configuration
- Plan PDN simulation and measure impedance and ripple with correct probing and VNA technique
Who it is for
- Hardware engineers designing boards around FPGAs, SoCs, processors or fast ADCs and DACs
- PCB layout engineers responsible for decoupling, planes and via placement on dense boards
- Signal and power integrity engineers who want a structured, numbers-first review of PDN design
- Test and validation engineers who measure rail ripple and PDN impedance
Syllabus
Module 1: Foundations: The PDN and Target Impedance
What power integrity is, the parts of a power distribution network and the band each one serves, and how to set a target impedance.
- What Power Integrity Is and the Parts of a PDN
- Target Impedance: The Calculation and Its Limits
- Reading a PDN Impedance Profile
- Module quiz (5 questions)
Module 2: Capacitors, Mounting and Planes
How real capacitors behave, why the mounting loop often matters more than the part, and what planes really contribute.
- Real Capacitors: ESR, ESL, Resonance and Derating
- Mounting Inductance and Via Placement
- Plane Pair Capacitance and Spreading Inductance
- Module quiz (5 questions)
Module 3: Decoupling Strategy and Anti-Resonance
Why mixed capacitor values create impedance peaks, how to control them, and how to build and review a decoupling scheme with numbers.
- Anti-Resonance Between Capacitor Values
- A Practical Decoupling Strategy
- Reviewing Vendor Recommendations
- Module quiz (5 questions)
Module 4: DC Drop, Current and Ground Bounce
Size copper and vias for DC drop and current, apply remote sense correctly, and estimate and reduce ground bounce and simultaneous switching noise.
- DC Voltage Drop in Planes and Copper
- Current Density and Via Current
- Remote Sense
- Ground Bounce and Simultaneous Switching Noise
- Module quiz (5 questions)
Module 5: Simulation and Measurement
Simulate a PDN with the right models, measure milliohm impedances with a VNA shunt-through set-up, and probe ripple without measuring the probe.
- Simulating a PDN
- Measuring PDN Impedance with a VNA
- Measuring Ripple and Probing Rails
- Module quiz (5 questions)
Free downloads for this course
- Trace Width and Current Reference (Reference)
Discuss your project
Email support@aavico.com or use Get in Touch when the website finishes loading.