Schematic Capture and Design Review

Draw schematics that layout, firmware, test and purchasing can trust, and review them before they cost a respin.

Learn to capture a circuit that other people can build from. This course covers trustworthy symbol and footprint libraries, sheet structure and net naming, datasheet-driven calculations for resistors and capacitors, schematic-level protection, the electrical rules check, a structured design review and a clean handoff to layout.

Beginner · 5 modules · 15 lessons · free certificate

About this course

Most board respins start on the schematic, not in layout. A pull-up that was never fitted, a regulator without the output capacitor its datasheet demands, a footprint whose pad numbers do not match the symbol, or a net label with a typo that splits one signal into two: each of these passes quietly into layout and is only found on the bench. This course teaches the habits and checks that catch them while they still cost minutes to fix.

You will start with what a schematic is for and who reads it, then build trustworthy libraries, organise sheets, nets, rails and reference designators, and carry part attributes through to the bill of materials. A full module works through the everyday design calculations straight from datasheets: pull-ups, LED and divider resistors, regulator capacitors and decoupling. You will add basic protection against reverse polarity, ESD and overcurrent, understand what the electrical rules check can and cannot tell you, run a structured review and hand a complete package to the layout designer.

The course assumes basic circuit knowledge: Ohm's law, and what resistors, capacitors, diodes and transistors do. It is tool-neutral, with examples that apply to KiCad, Altium and similar packages. Placement and routing are covered in PCB Layout Fundamentals: Placement and Routing, and regulator design in depth in Power Supply Design for PCBs.

Before you start: Basic circuit theory (Ohm's law, series and parallel resistors, what a capacitor and a diode do) and some familiarity with any schematic capture tool. PCB Basics for Beginners in the AAVICO Academy is useful background but not required.

What you will learn

  • Build and verify symbol and footprint library parts so pin and pad numbering can be trusted
  • Organise a schematic with clear sheets, net names, power rails, reference designators and BOM attributes
  • Read a datasheet critically and calculate pull-up, LED, divider and capacitor values with margins
  • Add basic reverse polarity, ESD and overcurrent protection at the schematic stage
  • Run an electrical rules check, interpret its results and recognise what it cannot find
  • Carry out a structured self-check and peer review, and hand the design to layout with clear constraints

Who it is for

  • Engineers and students drawing their first or second production schematic
  • Firmware and software engineers who want to read and review hardware designs with confidence
  • Layout designers who want to understand what a complete schematic handoff should contain
  • Makers and startup founders moving from development boards to a custom PCB

Syllabus

Module 1: Schematics and Libraries

What a schematic is for, who reads it, and how symbol and footprint libraries are built and kept trustworthy.

  1. What a Schematic Is For and Who Reads It
  2. Symbols, Footprints and the Link Between Them
  3. Keeping Libraries Trustworthy
  4. Module quiz (5 questions)

Module 2: Organising the Schematic

Sheet structure, net naming, power rails, reference designators and the part attributes that become the BOM.

  1. Sheet Structure: Flat and Hierarchical Designs
  2. Net Naming, Power Symbols and Rails
  3. Reference Designators and Part Attributes
  4. Module quiz (5 questions)

Module 3: Datasheets and Design Calculations

Read datasheets critically, then calculate pull-ups, LED and divider resistors, regulator capacitors and decoupling with sensible margins.

  1. Reading a Datasheet Critically
  2. Resistor Calculations: Pull-ups, LEDs and Dividers
  3. Regulator Capacitors and Decoupling
  4. Module quiz (5 questions)

Module 4: Protection and the Electrical Rules Check

Add reverse polarity, overcurrent and ESD protection at the schematic stage, then use the electrical rules check knowing what it can and cannot find.

  1. Reverse Polarity and Overcurrent Protection
  2. ESD and Interface Protection
  3. The Electrical Rules Check and Its Limits
  4. Module quiz (5 questions)

Module 5: Design Review and Handoff to Layout

Check your own schematic systematically, run a peer review that finds real problems, and hand a complete package to the layout designer.

  1. The Self-Check
  2. Running a Peer Review
  3. Handing Off to Layout
  4. Module quiz (5 questions)

Free downloads for this course

Enrol for free

Discuss your project

Email support@aavico.com or use Get in Touch when the website finishes loading.