Hardware Bring-up and Validation

Power a new board safely, get it working subsystem by subsystem and prove it meets its requirements.

Learn to bring up a new board without destroying it and then prove it works. Plan the bring-up, set up the bench, power up with current limits, get clocks, debug and peripherals running, find and patch faults, then verify the design with traceable tests, characterisation, margin and environmental testing.

Intermediate · 5 modules · 17 lessons · free certificate

About this course

The first boards back from assembly are the most valuable and the most fragile hardware a project will ever own. They may carry a reversed regulator, a footprint drawn from the wrong datasheet view or a strap resistor that sends the processor into the wrong boot mode, and there are only a handful of them. A careless first power-up can destroy the board that would have revealed the fault, and a poorly recorded bring-up leaves the same faults waiting on the next revision.

This course follows a board from the day the bring-up plan is written to the day the change notes for the next revision are issued. It covers preparation and the lab bench, first power with current limits and rail checks, clocks, resets, debug connection and peripherals, a disciplined approach to debugging, measuring correctly, common faults and safe rework. It then moves to design verification: test cases traced to requirements, characterisation across voltage and temperature, margin testing, signal integrity and power measurements, environmental and reliability testing at a concept level, and the records that carry lessons into the next build.

The course builds on the EVT, DVT and PVT stages described in Taking a Product to Production and goes deeper on the engineering work inside them. Certification testing is covered in Regulatory Compliance for Electronic Products, and production test in Design for Assembly and Test. Figures from standards are named; bench figures are typical and depend on your design. A course certificate records completion of the course only.

Before you start: You should be able to read a schematic, use a multimeter and an oscilloscope at a basic level, and know the prototype stages described in Taking a Product to Production. Some familiarity with microcontrollers at the level of Embedded Firmware Fundamentals helps in Module 2.

What you will learn

  • Write a bring-up plan and decide what to order and prepare with the first boards
  • Power a new board safely using resistance checks, current limits and rail-by-rail checks
  • Bring up clocks, resets, the debug connection and each peripheral in a logical order
  • Debug systematically, measure without fooling yourself and rework boards safely
  • Write traceable test cases and run characterisation, margin and environmental tests
  • Record results, track issues and produce clear design change notes for the next revision

Who it is for

  • Hardware engineers who will power up and debug their own boards
  • Firmware engineers who join bring-up and need to work safely at the bench
  • Test and validation engineers who write and run design verification tests
  • Engineering leads who plan prototype builds and decide when a design is ready for the next stage

Syllabus

Module 1: Preparing for Bring-up

The bring-up plan, test firmware and fixtures, what to order with the first boards, and the instruments a bring-up bench needs.

  1. Writing a Bring-up Plan
  2. Test Firmware, Fixtures and What to Order
  3. The Bring-up Bench and Its Instruments
  4. Module quiz (5 questions)

Module 2: First Power to Working Peripherals

Checks before power, powering up with current limits, rail sequencing and thermal checks, then clocks, resets, debug and peripherals one at a time.

  1. Checks Before Power: Inspection and Rail Resistance
  2. First Power with Current Limits
  3. Rail Sequencing, Thermal Checks, Clocks and Resets
  4. Debug Connection, First Code and Peripherals
  5. Module quiz (5 questions)

Module 3: Debugging Techniques and Rework

A disciplined debugging method, measuring without fooling yourself, the faults new boards most often have, and how to rework and patch boards safely.

  1. Debugging by Divide and Conquer
  2. Measuring Correctly and Probing Technique
  3. Common Faults on New Boards
  4. Reworking and Patching Prototype Boards
  5. Module quiz (5 questions)

Module 4: Design Verification

Test cases traceable to requirements, characterisation across voltage and temperature, margin testing, and signal integrity and power measurements.

  1. Writing Test Cases Traceable to Requirements
  2. Characterisation and Margin Testing
  3. Signal Integrity Checks and Power Measurements
  4. Module quiz (5 questions)

Module 5: Environmental Testing and the Next Revision

Temperature and humidity testing, vibration, shock and HALT/HASS at a concept level, and the records, issue tracking and change notes that feed the next board revision.

  1. Temperature Cycling and Humidity Testing
  2. Vibration, Shock, HALT and HASS
  3. Recording Results, Tracking Issues and Change Notes
  4. Module quiz (5 questions)

Free downloads for this course

Enrol for free

Discuss your project

Email support@aavico.com or use Get in Touch when the website finishes loading.