Controlled Impedance and Transmission Lines

Understand, calculate, build and measure PCB traces that hold their impedance from driver to receiver.

Learn how PCB traces behave as transmission lines and how to get the impedance you designed. Covers L, C and Z0, microstrip, stripline and coplanar structures, differential pairs, formulas versus field solvers, manufacturing effects and tolerances, TDR coupons, loss and the targets of common interfaces.

Intermediate · 5 modules · 17 lessons · free certificate

About this course

An impedance target on a fabrication drawing is the end of a long chain of reasoning: the physics of a wave travelling between a trace and its reference plane, the geometry and materials that set the line's inductance and capacitance, the way a pair of traces couple, and the etching, plating and lamination processes that turn a drawing into copper and glass. This course follows that chain from first principles to a measured TDR trace, so that you can choose structures with confidence, judge a fabricator's stackup proposal and understand why a coupon reads what it reads.

The emphasis is practical. You will work with Z0 = sqrt(L / C) and effective dielectric constant, use a well-known closed-form microstrip approximation within its stated range, see why the final numbers should come from the fabricator's field solver, and learn which manufacturing effects move impedance and by roughly how much. Material values and tolerances are given as typical ranges; your fabricator's data always takes precedence, and interface targets must be checked against the relevant specification and the chip vendor's layout guidelines.

The short lesson on specifying impedance in PCB Design for Manufacturing is assumed and extended here. Reflections, termination strategy, crosstalk budgets and eye diagrams are covered in Signal Integrity Fundamentals, and interface-specific channel rules for DDR, USB, PCIe and Ethernet are in High-Speed Interface Design. Full-wave electromagnetic modelling of vias and connectors is outside the scope of this course.

Before you start: You should be comfortable with basic circuit theory (resistance, capacitance, inductance) and have laid out at least one multilayer board. PCB Design for Manufacturing, and in particular its module on stackups and controlled impedance, gives useful background.

What you will learn

  • Explain characteristic impedance and propagation delay in terms of inductance and capacitance per unit length and effective dielectric constant
  • Choose between surface microstrip, embedded microstrip, stripline and grounded coplanar waveguide, and predict how geometry and Dk move their impedance
  • Relate odd-mode, even-mode, differential and common-mode impedance, and decide between tight and loose coupling for a pair
  • Use a closed-form approximation for a first estimate and explain why the fabricator's field solver should set the final geometry
  • Account for etching, plating, solder mask, resin content and glass weave, and set realistic tolerances
  • Read a TDR coupon result, describe the main loss mechanisms and look up interface impedance targets correctly

Who it is for

  • PCB designers who route impedance-controlled interfaces and want to understand the numbers they enter
  • Hardware engineers who review stackups, impedance tables and fabricator proposals
  • Engineers moving from low-speed boards to designs with fast edges, RF feeds or serial links
  • Test and quality engineers who read TDR coupon reports

Syllabus

Module 1: Transmission Line Fundamentals

Why fast edges turn traces into transmission lines, how L and C per unit length set Z0, and how effective Dk sets delay.

  1. When a Trace Becomes a Transmission Line
  2. Inductance, Capacitance and Z0
  3. Propagation Delay and Effective Dk
  4. Module quiz (5 questions)

Module 2: Microstrip, Stripline and Coplanar Structures

The cross-sections you will use, their strengths and weaknesses, and how geometry and Dk move their impedance.

  1. Surface and Embedded Microstrip
  2. Symmetric and Asymmetric Stripline
  3. Coplanar Waveguide with Ground
  4. Module quiz (5 questions)

Module 3: Differential Pairs

Odd and even modes, differential and common-mode impedance, coupling choices and how to route and terminate pairs.

  1. Odd Mode, Even Mode and the Impedances that Follow
  2. Tight and Loose Coupling
  3. Routing, Discontinuities and Termination of Pairs
  4. Module quiz (5 questions)

Module 4: Calculation and Manufacturing Effects

Closed-form approximations versus field solvers, what happens to a cross-section in fabrication, and how to set realistic tolerances.

  1. Closed-Form Approximations and Their Limits
  2. Field Solvers and Why to Trust the Fabricator's
  3. Etching, Plating and Solder Mask
  4. Resin Content, Glass Weave and Tolerances
  5. Module quiz (5 questions)

Module 5: Measurement, Loss and Interface Targets

How impedance is verified with coupons and TDR, how conductors and dielectrics cause loss, and how to find the right target for an interface.

  1. Test Coupons and TDR Measurement
  2. Conductor Loss, Skin Effect and Roughness
  3. Dielectric Loss and Loss Budgets
  4. Impedance Targets of Common Interfaces
  5. Module quiz (5 questions)

Free downloads for this course

Enrol for free

Discuss your project

Email support@aavico.com or use Get in Touch when the website finishes loading.