Power Supply Design for PCBs
Choose, calculate and lay out the regulators that power your board, then prove them on the bench.
Design the DC power supplies on your board with confidence. Build a power budget and architecture, size LDOs and buck converters with worked calculations, apply the layout rules that make switchers behave, add soft-start, protection, sequencing and supervision, and measure ripple, efficiency and transient response correctly on the bench.
Intermediate · 5 modules · 18 lessons · free certificate
About this course
Almost every board has a handful of regulators, and almost every board that misbehaves at bring-up has at least one of them to blame: a rail that oscillates, an LDO that runs too hot, a buck converter that rings and fails emissions, or a processor that starts before its supplies are ready. This course teaches the practical design of board-level DC power, from the power budget to the bench, with the reasoning behind each rule so that you can apply it to parts you have not used before.
You will build a power budget and choose an architecture, size linear regulators for dropout, dissipation, PSRR and stability, and work through a complete buck converter design in plain-text calculations: duty cycle, inductor, output and input capacitors, and losses. Boost, buck-boost and charge pumps are covered briefly. Switching regulator layout gets the most attention, because it decides whether a good schematic works: the hot loop, input capacitor placement, the switch node, feedback routing, ground return and thermal pads. The course then covers control loops at a concept level, inrush and fault protection, sequencing and supervision, and how to measure ripple, efficiency, transient response and loop stability.
Out of scope: the detailed design of decoupling networks and plane impedance (see Power Integrity and PDN Design), emissions and immunity in depth (see EMC by Design: Grounding, Shielding and Layout), and off-line AC-DC (mains) supply design, which is mentioned only to note its safety requirements. A course certificate records completion of the course; it is not a professional qualification.
Before you start: You should be comfortable with Ohm's law, basic inductor and capacitor behaviour, reading datasheets and drawing schematics, and you should have laid out or reviewed at least a simple board. Schematic Capture and Design Review and PCB Layout Fundamentals: Placement and Routing in the AAVICO Academy cover useful background.
What you will learn
- Build a power budget and choose a rail architecture with intermediate buses and post-regulators
- Select and size LDOs for dropout, dissipation, PSRR, noise and output capacitor stability
- Calculate the duty cycle, inductor, capacitors, ripple and losses of a buck converter
- Lay out a switching regulator with a minimal hot loop, quiet feedback and a sound thermal pad
- Add soft-start, inrush limiting, reverse polarity, overcurrent and overvoltage protection, sequencing and resets
- Measure ripple, efficiency, transient response and loop stability without fooling yourself
Who it is for
- Hardware engineers who design boards with several supply rails and want a structured method
- PCB layout engineers who place and route switching regulators and need to know what really matters
- Embedded and firmware engineers who own a board's power design on a small team
- Test and validation engineers who measure rails, efficiency and transient response
Syllabus
Module 1: Power Architecture and Linear Regulators
Build a power budget, choose a rail architecture, and size linear regulators for dropout, dissipation, PSRR, noise and stability.
- The Power Budget and Rail Architecture
- Linear Regulators: Dropout and Dissipation
- LDO PSRR, Noise and Output Capacitor Stability
- Module quiz (5 questions)
Module 2: Buck Converters in Detail
How a buck converter works, then a complete worked design: duty cycle, inductor, output and input capacitors, conduction modes and efficiency losses.
- How a Buck Converter Works
- Choosing the Inductor
- Output and Input Capacitors
- Efficiency and Where the Losses Go
- Module quiz (5 questions)
Module 3: Other Topologies and Switching Regulator Layout
Boost, buck-boost and charge pumps in brief, then the layout that decides whether a switcher works: the hot loop, switch node, feedback, ground and thermal pad.
- Boost, Buck-Boost and Charge Pumps
- The Hot Loop and Input Capacitor Placement
- Switch Node, Feedback Routing and Ground Return
- Thermal Pads and a Layout Review Checklist
- Module quiz (5 questions)
Module 4: Control Loops and Protection
Control loops, compensation and stability at a concept level, then inrush, soft-start, load switches and protection against reverse polarity, overcurrent and overvoltage.
- Control Loops, Compensation and Stability
- Inrush, Soft-Start and Load Switches
- Reverse Polarity, Overcurrent, Overvoltage and eFuses
- Module quiz (5 questions)
Module 5: Sequencing, Supervision and Bench Measurement
Power sequencing, supervisors, resets and power-good, then how to measure ripple, efficiency, transient response and loop stability on the bench.
- Power Sequencing
- Supervisors, Resets and Power-Good
- Measuring Ripple and Efficiency
- Measuring Transient Response and Loop Stability
- Module quiz (5 questions)
Free downloads for this course
- Board Bring-up Checklist (Checklist)
- EMC Design Checklist (Checklist)
- Schematic Design Review Checklist (Checklist)
- Trace Width and Current Reference (Reference)
Discuss your project
Email support@aavico.com or use Get in Touch when the website finishes loading.