PCB Fabrication Processes in Depth

Follow a multilayer board through every fabrication step, and learn what each one means for your design.

Go inside the board shop. This course follows a multilayer PCB from CAM and inner layer imaging through lamination, drilling, plating, outer layers, solder mask and surface finishes to routing, electrical test, microsections and IPC-6012 acceptance, explaining the process behind each step and the defects it can cause.

Intermediate · 5 modules · 18 lessons · free certificate

About this course

Most design rules are really process limits in disguise. A minimum spacing is set by how copper etches, an aspect ratio by how plating solution reaches the middle of a hole, an annular ring by how far layers move in the lamination press. When you understand what happens to your data after it leaves the layout tool, you can read a fabricator's capability sheet critically, answer engineering queries quickly, choose a surface finish for the right reasons and interpret a microsection report rather than filing it.

This course walks through a typical multilayer process in the order a panel meets it: front-end engineering, inner layers, lamination and registration, mechanical and laser drilling, desmear and hole metallisation, plating, outer layers, solder mask and legend, the common surface finishes with their honest trade-offs, then profiling, electrical test, final inspection and acceptance to IPC-6012 and IPC-A-600. Process figures are labelled as typical because they vary between fabricators, chemistry suppliers and equipment.

It goes well beyond the short overview in PCB Basics for Beginners, and it complements PCB Design for Manufacturing, which covers the design rules themselves. It does not cover assembly, which has its own course, and it touches HDI, flex and high-frequency materials only where they change the process. It is not a training or certification programme for any IPC standard.

Before you start: You should know how a PCB is constructed and have seen or produced a set of fabrication files. PCB Basics for Beginners covers the background, and PCB Design for Manufacturing is useful but not required.

What you will learn

  • Explain each stage of multilayer fabrication, from CAM and inner layer imaging to profiling and test
  • Relate common design rules to the process limits behind them, such as etch factor, registration and throwing power
  • Answer engineering queries and write fabrication notes that state clearly what may and may not change
  • Compare HASL, OSP, immersion silver, immersion tin, ENIG, ENEPIG and hard gold, including their failure modes
  • Read a microsection or coupon report and judge it against IPC-6012 and IPC-A-600 requirements for the chosen class

Who it is for

  • Hardware and layout engineers who want to understand what their fabricator actually does with their data
  • Engineers who review fabricator capability, engineering queries, microsection reports and finish choices
  • Quality, supplier and procurement staff who qualify or audit bare board suppliers
  • Engineers moving into PCB manufacturing, CAM or process roles who need a structured overview

Syllabus

Module 1: Front-End Engineering and Inner Layers

How CAM prepares your data and panel, then how inner layer cores are cleaned, imaged, etched, inspected and bond treated.

  1. CAM, DFM Review, Engineering Queries and Working Panels
  2. Inner Layer Imaging: Cleaning, Dry Film and Exposure
  3. Etching, Stripping, Inner Layer AOI and Bond Treatment
  4. Module quiz (5 questions)

Module 2: Lamination, Registration and Drilling

How cores and prepreg are pressed into one panel, how layers are kept in register, and how holes are drilled mechanically, by laser and by back-drilling.

  1. Lay-up and the Lamination Press Cycle
  2. Layer Registration and X-ray Drilling of Targets
  3. Mechanical Drilling
  4. Laser Drilling, Back-Drilling and Hole Wall Quality
  5. Module quiz (5 questions)

Module 3: Hole Metallisation, Plating and Outer Layers

How drilled holes are cleaned and made conductive, how copper is plated to the thickness IPC-6012 requires, and how the outer layer pattern is formed.

  1. Desmear and Etchback
  2. Electroless Copper and Direct Metallisation
  3. Panel Plating, Pattern Plating and Throwing Power
  4. Outer Layer Imaging, Etch Resist and Etching
  5. Module quiz (5 questions)

Module 4: Solder Mask, Legend and Surface Finishes

How LPI solder mask and legend are applied, then the process, strengths and failure modes of each common surface finish.

  1. LPI Solder Mask, Via Protection and Legend
  2. HASL, OSP, Immersion Silver and Immersion Tin
  3. ENIG, Black Pad, ENEPIG and Hard Gold
  4. Module quiz (5 questions)

Module 5: Profiling, Test and Acceptance

How boards are cut out, electrically tested and inspected, how coupons and microsections provide evidence, and how IPC-6012 and IPC-A-600 define acceptance.

  1. Profiling: Routing, V-Scoring and Edge Features
  2. Bare Board Electrical Test: Flying Probe and Fixtures
  3. Final Inspection, Coupons and Microsections
  4. IPC-6012 and IPC-A-600 Acceptance
  5. Module quiz (5 questions)

Free downloads for this course

Enrol for free

Discuss your project

Email support@aavico.com or use Get in Touch when the website finishes loading.