Technical FAQs
Short technical answers to the questions that come up while specifying a board: layout inputs, fabrication options, stencils, sourcing and assembly. For the numbers behind them, see the capability pages.
PCB layout
What do you need to start a PCB layout?
A schematic and a bill of materials, plus the board outline, mounting holes, connector positions and any height limits. Tell us about impedance, high-current or sensitive circuits too.
What do I receive at the end of a layout project?
Typically the full Gerber set with drill, paste and outline layers, the placement file, the final BOM, a netlist and PDF prints. Native design files and other deliverables are agreed when the project is scoped.
How many layers do I need?
Simple circuits fit on one or two layers. Dense digital designs, fast interfaces and boards that need solid ground and power planes usually need four or more. Our stackup guide goes through the trade-offs.
Can you convert an old through-hole design to surface mount?
Yes, as a redesign project. Send the existing files or a sample board and we will scope the work.
Can I make changes once the layout has started?
Small changes are usually fine early on. Changes after review milestones may affect the schedule and price, so settle the schematic and BOM before layout begins where you can.
Fabrication
What board sizes can you make?
Single boards from 20 x 20 mm up to 430 x 585 mm in FR-4. Smaller boards are made in a panel. Size limits for other materials are on the rigid PCB capabilities page.
What does Tg mean?
Tg is the glass transition temperature of the laminate resin, where it changes from rigid to soft and expands much faster. High-Tg material keeps plated holes reliable through lead-free soldering and in hot environments. See materials and specifications.
What is the difference between starting copper and finished copper?
Starting copper is the foil on the laminate before processing. Outer layers are then plated, so finished copper on the surface is thicker than the starting foil. Track and gap limits depend on the starting weight.
Which surface finish should I choose?
ENIG for fine-pitch parts and BGAs, lead-free HASL for general boards on a budget, immersion tin for flat solderable pads and hard gold for edge connectors. Our surface finishes article compares them.
Is RoHS compliance the same as a lead-free finish?
No. RoHS restricts hazardous substances in the whole product. A lead-free finish is needed for a RoHS board, but the laminate, mask and components must comply too.
What is controlled impedance?
Fast and RF signals behave as transmission lines, so their trace impedance must match the source and load. We build the stackup and trace widths to a target such as 50 Ω single-ended or 90 or 100 Ω differential and measure test coupons to confirm it.
What are peel-off mask, carbon contacts and hard gold tabs?
Peel-off mask is a removable rubbery coating that protects holes, pads or contacts during soldering. Carbon contacts are printed conductive ink used for keypads and jumpers. Hard gold tabs are thick electroplated gold on edge connectors that are plugged in and out repeatedly.
What are bevelling and countersinking?
Bevelling grinds a chamfer along an edge connector so it slides into its socket, usually at 20 to 45 degrees. A countersink is a conical recess at a hole so a flat-head screw sits flush.
What is V-scoring?
A V-shaped groove cut from both faces along a straight line between boards in a panel, leaving a thin web that snaps cleanly. It suits rectangular boards; irregular shapes are tab-routed. See the panel guidelines.
How close can copper come to the board edge?
Our standard minimums are 0.20 mm on outer layers and 0.25 mm on inner layers for routed edges, and 0.40 and 0.45 mm for scored edges. Leave more where space allows, especially near connectors and mounting points.
Do you have standard stackups?
Yes. Tell us the layer count, thickness and impedance targets and we will propose a standard stackup that suits them. See materials and specifications.
What happens if you find a problem in my files?
Our engineers send you an engineering query by email describing the issue and a proposed fix. Production waits for your answer, so a quick reply keeps the schedule.
How do I work out the gold area on my board?
Add up the area of all copper left exposed by the solder mask, which is what the finish covers, and divide it by the board area to get a percentage. Your Gerber viewer can usually measure it from the mask layer.
Stencils
What does a stencil do?
It controls how much solder paste lands on each surface-mount pad, so every joint gets enough solder for a sound electrical and mechanical connection without bridging.
Framed or frameless?
Frameless foils fit a reusable tensioning frame and cost less, which suits prototypes. Framed stencils are bonded into a fixed frame for production printers. See stencil capabilities.
Why do I need separate stencils for the top and bottom?
Each side with SMD parts is printed separately, so each needs its own stencil.
How does stencil thickness affect assembly?
Thickness and aperture size set the paste volume. Too much causes bridging on fine-pitch parts, too little gives weak joints. The finest pitch on the board usually decides the thickness.
Can a stencil be reused, or cover several designs?
Yes to both. Stainless stencils last for many prints when cleaned properly, and one stencil can carry several designs that are printed together in a panel.
Component sourcing
What is a bill of materials?
The list of every part needed to build the board: manufacturer part numbers, descriptions, reference designators and quantities. It is the basis of both the sourcing quote and the assembly set-up.
Where do you buy components?
From authorised distributors and manufacturers, so parts are traceable. If a part is scarce, we propose alternatives for you to approve rather than buying from unverified sources.
Can you use parts from my own supplier?
Yes. Order them yourself and have them delivered to us for a consigned build, packed as described in the component packaging guidelines.
Can you buy only part of the BOM?
Yes. Mark which lines you will supply and we will source the rest.
Assembly
What is the difference between SMD and through-hole parts?
Surface-mount devices sit on pads on the board surface and are reflow soldered; they are smaller and suit automated placement. Through-hole parts have leads that pass through plated holes and are wave, selectively or hand soldered; they give strong joints for connectors and heavy parts.
What are BGA and TQFP packages?
A BGA (ball grid array) has solder balls in a grid under the body, giving many connections in a small area; its joints are checked by X-ray. A TQFP (thin quad flat package) has fine gull-wing leads on four sides and is inspected optically.
What do assembly side and stencil side mean?
Assembly side is where parts are fitted: top, bottom or both. Stencil side is where SMD parts need paste. A board with only through-hole parts needs no stencil.
Is assembly automated?
Yes. SMT parts are printed, placed by machine and reflowed, then inspected by AOI, with X-ray for hidden joints. Through-hole and odd-form parts are soldered by wave, selective soldering or hand as the design requires.
What is conformal coating and do you offer it?
A thin protective film over the assembled board that guards against moisture, dust and corrosion. Acrylic, silicone, polyurethane, epoxy and parylene coatings each balance protection against ease of rework. Ask for it in your quote, with the coating type and any areas that must stay uncoated.
How many extra parts should I send for a consigned build?
Small SMD passives need extras for feeder leaders and pick losses, from a fixed number of pieces on small orders to a few percent on large ones. Through-hole parts need 1% extra. The component packaging guidelines give the full table.
Can you fit only some of the parts?
Yes. Mark the parts that must not be fitted as DNP in the BOM, or send a BOM with only the parts you want assembled.
Ready when your files are
Send your design for a quote
Upload your Gerber, drill and assembly files with the quantities you need. Our engineers check them against these guidelines and come back with a price, a schedule and any questions.